Dialed In Pendant

Menu

Dialed In Pendant

Level
Intermediate
Session
1, 4 hour sessions, on-line
Description
Precision will be the key to dialing in this project. We will work with mixed metals and set a stone to create depth and interest. Students who are successful will have a pendant that is kinetic.

Tools

Tools required to complete project.

  • Bench Block

    Steel or Anodized aluminum - Used as a hammering surface for metal stamping or working with metal.

  • Bezel Shears

    Used to cut metal sheet. There are many available on the market, any of which will work, however they should NOT be serrated. (Tin snips or airplane shears will also work, however, they may be large and cumbersome.) If the project has curves in the design and you own a pair, bring curved bezel shears. This is an optional item for most classes. Shears will be provided for use during classes.

  • Brass brush

    Used for cleaning or surface texturing on soft metals.

  • Chasing Hammer

    Used for chasing/moving metal. In my classes chasing hammers are used to create hammer marks on metal and riveting. Instructor will provide for every class needed.

  • Curved Burnisher

    Used to burnish or smooth the surface of metal. For most projects using this tool you will want at least a 3mm ball. This tool may also be found at your local craft store for use with clay or nail art.

  • Fine Tweezers

    Used for moving small parts. Classes requiring fine tweezers will not work with fire tweezers. These are a cheap investment. Please be bring some. Optional for most classes.
  • Tool Flex Shaft

    Flex shaft

    Rotary tool used for polishing, drilling, finishing, etc. Flex shafts are available for purchase new and gently used at the class. Pleased contact the instructor if are interested in purchasing one at the class as quantities are limited. 

  • Hand Tools

    Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.

    • Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
    • Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
    • Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
       

  • Heavy Duty Cutters

    Although any heavy duty cutter will work, if they are flush, they will make your work a lot easier. Cutter should be able to cut through 10g wire. (Many cutters imprint their cutting capacity on the inside of the handle.) Keiba and Xuron are recommended.

  • Helping Hand/Third Hand

    Used to hold small parts in place while soldering. Instructor will provide to share for every class needed.

  • Hoop Mandrel

    Bigger than a ring mandrel and smaller than a bracelet mandrel, made of steel and used for forming round shapes. Not mandatory but so helpful.
  • Tool Magnifier or Optivisor

    Magnifier or Optivisor

    – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.


  • Multi-looping Pliers

    Optional unless stated, used in to create consist sized loops. Typically optional in my classes. Round nose may be use its place for most projects.
  • Tool Ott Light or Task Lamp

    Ott Light or Task Lamp

    This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.

  • Rawhide/Leather Mallet

    Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubber one may not.

  • Riveting Hammer

    (aka Swiss Hammer) – Best hammer for riveting due to its small size. Instructor will provide for every class needed.

  • Soldering Kit

    (Optional) 
    Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements.

  • Student Files

    Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.
Facebook Twitter Pinterest