Serene Pendant

Menu

Serene Pendant

Level
Intermediate
Sessions
4 hours
Descrption
This classic and serene pendant is perfect for making your everyday wear a little more special. We will make an open back setting to allow the light to shine through and finish it off with a little fun using a kinetic bail.

Tools

Some tools will be provided by the instructor. Please refer to your registration.

  • Bench Block

    Steel or Anodized aluminum - Used as a hammering surface for metal stamping or working with metal.

  • Bench Pin

    There are a variety of bench pins available on the market, any will do. However, you will need to bring a 4” or larger C-clamp. As the C-clamp provided with a bench pin does not fit most tables at the shows. 

  • Bezel Pusher

    Not a tool I usually use, but from time to time they are helpful. Before using, consider sanding the edges of the tool to create a bevelled edge to reduce marring and scratches.

  • Bezel Rocker

    There are 2 bezel rockers on the market, the one shown is preferred, but if you own the other one it will work also. I usually have 2 to share at the shows.
  • Tool Broach

    Broach

    A five-sided tapered file of sorts used to clear the inside of a tube.
  • Tool C-clamp

    C-clamp

    To be used with bench pins to clamp to tables. May be found at any local hardware store. Must be at least 3 inches. 

  • Cut Lube

    Used to lubricate saw blades and drill bits for ease of cutting.

  • Divider

    Used to score metal to create lines for cutting. May also be used to aid in measuring for consistency. A compass will NOT work, I already tried.
  • Tool Flex Shaft

    Flex shaft

    Rotary tool used for polishing, drilling, finishing, etc. Flex shafts are available for purchase new and gently used at the class. Pleased contact the instructor if are interested in purchasing one at the class as quantities are limited. 

  • Hand Tools

    Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.

    • Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
    • Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
    • Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
       

  • Helping Hand/Third Hand

    Used to hold small parts in place while soldering. Instructor will provide to share for every class needed.

  • Jeweler’s Saw

    Used for cutting sheet metal and metal tubes. Instructor will provide for every class needed.
  • Tool Magnifier or Optivisor

    Magnifier or Optivisor

    – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.


  • Muslin buffing wheels

    Used with a flex shaft or Dremel to polish metal.

  • Needle File Set

    Used for filing smaller pieces of metal and tight places. When required, either diamond coated or fine tooth is preferred. Some students may prefer to use smaller files as opposed to the student files for their projects.

  • Nylon nose parallel pliers

    – Parallel action provides even pressure while holding firm. I love using nylon parallel pliers to manipulate my metal. Parallel pliers were my favorite pliers until they made nylon nose parallel pliers. For almost all projects these pliers are optional. You may use regular nylon nose and parallel nylon nose interchangeably.
  • Tool Ott Light or Task Lamp

    Ott Light or Task Lamp

    This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.

  • Rawhide/Leather Mallet

    Shape and flatten metal without marring it. #2 mallet is a standard size. Instructor will provide for every class needed. A yellow nylon mallet may be used in its place, however a rubber one may not.

  • Metal Ruler

    6" metal ruler is preferred unless otherwise noted. A larger one will also work, however, it may be a little cumbersome.

  • Soldering Kit

    (Optional) 
    Items in this Soldering Kit will be provided for use during the class. If you are interested in ordering a kit please click on the image. Kit includes: Butane torch, butane, 1 tube solder paste, fire tweezers, copper tweezers, Sparex, tripod with mesh, flux, soldering board. (Note: kit will be delivered at class. If you require the kit prior to class please contact us to make arrangements.

  • Soldering Pick

    A small, pointed instrument designed to help you move solder into place.

  • Student Files

    Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.

  • Tube Cutting Pliers

    A great gadget to aid in cutting tubes. These pliers create even leverage on the tube for sawing. Provided for all classes with tubes.
Facebook Twitter Pinterest