Kaleidoscope

Menu

Kaleidoscope

Level
Intermediate
Session
3 hours
Description
Combine transparent and opaque enamels to create a kaleidoscope of colors. Using a series of multiple torch firings we will create a special effect that will dazzle the eye. This is listed as an intermediate class because the basics will not be covered during the class time so that we can focus on the technique and get right to work creating.

Tools

Some tools will be provided by the instructor. Please refer to your registration.

  • Butane Torch

    Great for small soldering projects, annealing and torch fired enameling. Instructor will provide torch and butane for every class needed. (1 for every 2 students for most classes other than basic soldering.)

    Pistol style torches may be used interchangeably to the MaxFlame torches. Its larger head is great for heavy or larger projects.

  • Tool Dust Mask

    Dust Mask

    A MUST if you want to drill shells and pearls. However, this is optional for classes with fumes such as etching and patinating. Classes that have a lot of dust do not require a mask, but it up to you if are you sensitive. (ie enameling.) Dust masks may be purchased at any hardware store.

  • Enamel Kit

    Items in this Enamel Kit including enamels will be provided for use during in person classes. Thus is considered optional. If you are interested in ordering a kit please click on the image. Enamel kit includes: trivet, sifter, Penny Brite, alundum stone, choice of one color kit, and Klyr Fire.

    Jewel Tones

    Earth Tones

    Cool Tones

  • Fire Tweezers

    Used for handling hot metal. A must in soldering situations. Instructor will provide for every class needed.

  • Hand Punch

    1.25, 1.5, 1.8 mm. Used to make holes in metal. Please refer to class details for size needed.

  • Hand Tools

    Basic hand tools – Any quality is appropriate for my classes. These do not need to be high end or expense.

    • Round nose - Typically it is preferred that the round nose be a fine tip. Especially for classes with detailed wire work.
    • Chain/needle nose – Tapered jaws for general metal and wire work. Non-serrated are requested for all of my classes. Typically requested for classes to be used for opening and closing jump rings; in which case, 2 pairs are requested or a combination of chain nose and flat nose is suitable.
    • Flat nose – Similar to chain nose but the jaws are not tapered. Non-serrated are requested for all of my classes.
       
  • Tool Magazine pages

    Magazine Pages

    Magazine pages of any kind – Take your pick. Or just grab one of the programs at the show.
  • Tool Magnifier or Optivisor

    Magnifier or Optivisor

    – For almost all classes this is listed as an “As Needed” tool. If you have sight challenges it is recommended that you are properly prepared. For advance stone setting classes this is required! If you decide to use reading glasses consider better than 2.5x.


  • Tool Ott Light or Task Lamp

    Ott Light or Task Lamp

    This is optional item that is listed for every class. It is up to you to determine whether or not you will need to have one depending on your vision.
  • Tool Paint Brush

    #2 Paint Brush

    Any small paint brush will work for these projects. A #2 brush was designated just to demonstrate that it needs to be small. Don’t bring a house painting brush! Just saying. This brush does not need to be expensive, a cheap disposable one will work.


    IF a #2 flat brush is designated, again just looking for a smaller sized brush.


  • Metal Ruler

    6" metal ruler is preferred unless otherwise noted. A larger one will also work, however, it may be a little cumbersome.

  • Student Files

    Standard size is 2/o. For filing metal. . Instructor will provide to share for every class needed.

  • Tripod with mesh

    By using a tripod instead of soldering board you are reducing heat sink. Tripods are also used for torch fired enameling. Instructor will provide for every class needed.

  • Two-hole draw down punch

    This is different from a hand punch as it has 2 sizes in one tool. Instructor will provide to share (1 for every 2 people) for every class needed.

  • Wood dap set

    Used to dap metal to create a convex/concave shape in metal.
Facebook Twitter Pinterest